Standard Pump Controllers - With SMS

• Enclosure:
  • IP56 rated, powder coated mild steel enclosure with inner door and removable gland plate
• Protection:
  • Pad-lockable mains power isolator switch
  • Circuit breaker protected low voltage control and input circuitry
  • Individual pump isolation
  • Contactor and thermal overload protection of pump motors
  • Din rail mounted terminal connections
• Control & interface:
  • Single or dual pump keypad interface:
    • Indicator lights for power on, high & low level alarm, pump run, pump fault/overload and prime loss
    • Push buttons for alarm mute/reset, pump auto/off/manual control
  • PCB control module with dipswitches for adjusting configuration
  • ME-Link IoT/SMS module (requires micro SIM card from network provider with CAT-M1 enabled)
  • Vandal resistant antenna (remote mount high gain antenna also available for low signal strength areas)
  • BMS interface board for ME-Link to pump controller interface
  • Battery for backup to ME-Link on mains power failure
  • Visual (strobe) and mutable audible (buzzer) alarms
  • Soft starter per pump with adjustable soft start and stop (Soft Start versions)
• Inputs:
  • Single phase (230Vac) or three phase (400Vac) power supply
  • 4x digital 12Vdc inputs for float or pressure switches, optional low flow switch
  • Standard terminal setup: Low level, pump stop, pump start and high level float switches
• Outputs:
  • 1 or 2x pump supply outputs
  • BMS volt free output for common fault
  • 2x relay outputs on ME-Link module for remote control

Function Features

• High level alarm delay
• Smart chirp mode alarms
• Manual pump control
• Duty sharing and alternation
• Pump staging and destaging
• Staggered pump start
• Level control mode
• Maintain minimum level
• Pressure control mode

Fault Protection

• Pump overload protection
• Pump anti-seize protection
• High level alarm
• Low level alarm 
• Low flow/prime loss protection
• Low pressure alarm

SMS Functions

• SMS messaging for high level alarm, pump faults and power/battery supply status
• Easy programming with SMS commands
• Up to 10 phone numbers can receive messages
• Smart help responses on incorrect commands
• Once, repeat or sequential notification messaging 
• Repeat or sequential messaging until user accepted
• Daily reminder messages for alarms that are still active
• Remote control of pumps or system via the 2 relay outputs
• Periodic test messages to ensure ME-Link is operating
• Temporary notification disable for site servicing
• Logged data for last alarm, accept time and accept number

Common Applications

• Submersible sewage
• Submersible stormwater
• Pressure boosting

Standard Pump Controllers - With SMS

Code	No of Pumps	Phase / Voltage	Overload Ratings	Soft Starter Ratings
FPC-15005-SMS	1	1 Phase / 230Vac	-AA to -E	N/A
FPC-15007-SMS	1	3 Phase / 400Vac	-AA to -E	-S4.0 to -S90
FPC-30020-SMS	2	1 Phase / 230Vac	-AA to -E	N/A
FPC-30040-SMS	2	3 Phase / 400Vac	-AA to -E	-S4.0 to -S90

Standard Pump Controllers - With BMS & SMS

Additional hardware features:

• Additional BMS interface board providing volt free BMS outputs for power on, high level, individual pump run and individual pump fault

Code	No of Pumps	Phase / Voltage	Overload Ratings	Soft Starter Ratings
FPC-15205-SMS	1	1 Phase / 230Vac	-AA to -E	N/A
FPC-15207-SMS	1	3 Phase / 400Vac	-AA to -E	-S4.0 to -S90
FPC-30220-SMS	2	1 Phase / 230Vac	-AA to -E	N/A
FPC-30240-SMS	2	3 Phase / 400Vac	-AA to -E	-S4.0 to -S90

Overload Rating Guide

Code Suffix	Amp Rating
-AA	1.6 - 2.5 Amp
-A	2.5 - 4 Amp
-B	4 - 6 Amp
-BB	5.5 - 8 Amp
-C	7 - 10 Amp
-D	9 - 13 Amp
-E	12 - 18 Amp

Additional overload ratings available on request

For FLCs greater than 18 Amps, soft starters are recommended

Soft Starter Guide

Code Suffix	kW Rating
-S4.0	4.0 kW
-S5.5	5.5 kW
-S7.5	7.5 kW
-S11	11 kW
-S15	15 kW
-S22	22 kW
-S30	30 kW
-S37	37 kW
-S45	45 kW
-S55	55 kW
-S75	75 kW
-S90	90 kW

Additional kW ratings up to 160kW available on request

Optional Modifications

• /BBHLS - With battery backup high level alarm
• /CON - With conductivity relays and inputs for common, stop, start and high level probes
• /GEN - With generator inlet socket and manual changeover switch
• /ATS - With automatic generator changeover switch
• /INT - With intrinsically safe input barrier relay and inputs for working and high level floats
• Pump thermistor inputs
• Mine spec enclosure
• 316 stainless steel enclosure
• Pump max run time protection